Unfortunately, even with the stated rating of 16 A, most valves quickly fail due to the weakening of the contact jaws. Therefore, this method of connection is fraught with the fact that the outlet will literally melt after a couple of years of operation..
Really high-quality household sockets for currents from 20 A and above the operating current of some VPs can reach 30 A can be difficult to find.
In any case, you can use industrial-design plug pairs, because most manufacturers of equipment do not have warranty conditions for the wire and plug.. If you cut the plug completely, you can place a compact junction box where the cable comes out of the wall. In it, the connection is made on a screw terminal block, the contacts of which are much more durable than most outlets.
If the cabinet and panel are mounted in the same kitchen section, you will only need one box. Naturally, you can avoid cable connections and leave a longer end that can be plugged directly into the input terminals. Most manufacturers provide this option and do not place warranty seals on the cover of the desired compartment.. The connection of the lines supplying the hob and the oven must be carried out with the unquestioning installation of a number of protective devices.
Currents of 15—35 A for household networks are considered significant, therefore it is better to abandon differential automatic machines and draw up a diagram on two separate devices. The first is an RCD, preferably of the highest quality possible. Since there are no other consumers on the line, you can choose devices from the category of increased sensitivity — about 10 mA.
The permissible current, of course, must correspond to the load. Some examples of modern technology have digital controls and a dashboard. Such devices are very sensitive to voltage surges, therefore appropriate protection in the form of surge protection devices must be provided.. Skip to content. Search for:. Home » Building » Engineering systems » How to install and connect an electric hob and oven. Reading 7 min Views 11 Published by September 28, While gas hobs can be effective, and have traditionally been a favourite of chefs, we find induction hobs generally out-perform them.
Also, electric ovens spread heat more evenly than gas. Switching from a gas oven, hob or cooker to electric may also require expensive work. If you are considering switching fuels, get quotes from two or three companies. The ECA Electrical Contractors' Association advises that electricians should be Part P registered in order to undertake certain electrical work in homes.
This can include new circuits and new consumer units. If in doubt, consult a suitably skilled and registered electrical contractor. Meanwhile if you're installing a gas hob or cooker, you will need to use a Gas Safe registered engineer. Many plumbers, who frequently deal with boilers, will be Gas Safe registered, but check the Gas Safe Register to be certain.
If you don't already know a trustworthy electrician or plumber, use Which? Trusted Traders to track down a local tradesperson endorsed by Which?. You can also use our Trusted Traders search tool below. More on this How to buy the best built-in oven Top five best single ovens for Oven temperature conversion table Built-in oven reviews. Related articles Which? Best Buy cooker hoods Hob reviews Range cooker reviews Which? Best Buy freestanding cookers.
Share on Facebook Share on Twitter Share by email. Latest News In Which? Five ways to help garden wildlife in winter. What should we review next? What does Ecodesign mean?
Best Currys sales deals revealed by Which? Connecting the hob may require a special power connector - RSh VSh , used in connection to two or three phases. The socket and plug should be purchased from the same manufacturer, preferably made of light plastic - such plugs and sockets are no different from their black carbolite counterparts. But the terminal block is simpler and more reliable. The wires in it are not just tightened, but are fixed with clamping screws.
In this case, the phases and neutral must be marked. In Soviet times and in the 90s, local grounding of sockets and terminal blocks was not used at home, it was replaced by grounding connecting to a zero wire. Practice has shown that the connection with zero may be lost, and the user will not be protected from electric shock. For two phases, respectively, the cable is 4-wire, for all three - for 5 wires. Phases are connected to terminals 1, 2 and 3, common zero and ground are connected to 4 and 5.
In a three-phase line, if the voltage is lost on one of the phases, the power output by the hob or oven will decrease accordingly. If a voltage of V is used, and one of the phases is disconnected, the power will be completely lost. Re-phasing changing the phases in places will not affect the operation of the product in any way.
After completing the installation and connection, we perform cleaning at the place of the work performed. The result is a fully operational equipment. Consider what you need to install a hob or oven. To install, do the following: we clarify the dimensions of the equipment, and carry out the marking of the tabletop at the installation site; put a mark from which the desired contour will be cut; insert a shallow saw into a jigsaw, cut along the markings and smooth the cut cut; remove sawdust and place the hob on the countertop; we apply glue-sealant or self-adhesive sealant to the cut; to protect the countertop from burning out, we put a metal tape under the hob; we put the surface in a previously prepared hole and connect the hob according to the wiring diagram indicated on the back of the product.
Consider the procedure for connecting a hob or oven. The color coding of wires is most often as follows: black, white or brown wire - line phase ; blue - neutral zero ; yellow - ground. To connect a powerful plug to the hob, do the following: remove one of the halves of the plug body by unscrewing the retaining screw; insert the cable and fastening the connector, fix it with a bracket; we remove the protective sheath of the cable and strip the ends of the wires; we fix the wires in the terminals, checking with the diagram; close the fork structure back and tighten the main screw.
0コメント